Sustainability impact assessment for local energy supplies' development – The case of the alpine area of Lake Como,Italy

The development of distributed energy systems has important environmental, social and economic implications. Local decision-making processes must be guided by a careful evaluation of the sustainability of production chains and alternative choices. The aim of this study is to explore if and how an integrated assessment can quantify the extent to which bioenergy supply chain development contributes to rural development and energy policy objectives. We applied a Sustainability Impact Assessment (SIA) for local bioenergy development in the alpine area of Lake Como (Italy). We modeled the local bioenergy chain in 2008 and eleven scenarios considering different biomass utilizations, mechanization levels, combustion technologies, and subsidies schemes at 2020. We calculated economic, social and environmental indicators. We interpret and discuss the scenario analysis in order to support the bioenergy planning under the light of its implications for the different policy aims and concerns.     

Electromagnetism-like algorithms for optimized tool path planning in 5-axis flank machining

Optimization of tool path planning using metaheuristic algorithms such as ant colony systems (ACS) and particle swarm optimization (PSO) provides a feasible approach to reduce geometrical machining errors in 5-axis flank machining of ruled surfaces. The optimal solutions of these algorithms exhibit an unsatisfactory quality in a high-dimensional search space. In this study, various algorithms derived from the electromagnetism-like mechanism (EM) were applied. The test results of representative surfaces showed that all EM-based methods yield more effective optimal solutions than does PSO, despite a longer search time. A new EM-MSS (electromagnetism-like mechanism with move solution screening) algorithm produces the most favorable results by ensuring the continuous improvement of new searches. Incorporating an SPSA (simultaneous perturbation stochastic approximation) technique further improves the search results with effective initial solutions. This work enhances the practical values of tool path planning by providing a satisfactory machining quality.     

主/次显示器视距设计对头部关节舒适度的影响

以视平线可与显示器中心重合为准,分别探讨显示器中心在视平线上方、下方时不同视距对头部关节舒适度的影响. 实验自变量为视距(眼睛与显示器中心的水平距离),因变量为头部关节舒适度. 实验结果显示:1)显示器中心在人视平线上方时,头部舒适性状态始终处于不舒适状态,此时视距与人的头部舒适性关系成正比,即视距越大,头部舒适性越好;2)显示器中心在人视平线下方时,头部关节舒适状态始终处于正常范围,舒适性程度随视距增大而减小.     

Bio-economic modelling for marine spatial planning application in North Sea shrimp and flatfish fisheries

Marine activities have been increasingly competing for space and reducing areas for fishing. The use of spatially explicit tools can assist the decision making process on defining the optimal location of closures for fishing due to these emerging activities.This paper presents the Spatial Integrated bio-economic Model for FISHeries (SIMFISH). In this model fishers behaviour is simulated based on optimal effort allocation. The added value of this model compared to other existing spatial management tools lies in the presence of (i) short and long term fishers behaviour (ii) spatial explicit stock and fleet dynamics and (iii) relatively low data requirements.As an illustration, SIMFISH is applied in this paper to estimate the impact of area closures in the North Sea. Overall area closures have a negative impact on the profitability of the fleets. This would be worsened with higher fuel prices and decreased stock productivity.     

Experimental and numerical analysis of aluminum-aluminum bolted joints subject to an indentation process

The increasing interest of the industry (especially automotive, aviation and marine) in the fastener joints (riveted, bolted, etc.) between metallic materials, has re-opened the study on the possibility to improve the performance of the drilled structure using plastic deformation processes.Indentation process, performed before the drilling operation, creates circumferential compression stresses around the hole which increase significantly the mechanical performance of the drilled structures.In this paper, static and the fatigue performances of aluminum–aluminum (AW 6082-T6) single-lap bolted joints are studied. In particular, the study compares the mechanical strength of only drilled single-lap bolted joints (OD specimens) and single-lap bolted joints subject to an indentation process (IP specimens). In order to determine the cycles to failure and the corresponding Wöhler diagram, several fatigue tests are performed. The analyses allow to determine the mechanical performance and the failure mode of the analyzed joints.Several numerical analysis, conducted in ANSYS environment on three-dimensional models of the single-lap joint, are focused on the evaluation of the residual stress on the indented plate and, in particular, to compare the stress distribution on both type of analyzed joints.     

Kissing bond detection in structural adhesive joints using nonlinear dynamic characteristics

In this paper, the effect of kissing bond on nonlinear dynamic behavior of structures with flexible adhesive joint is investigated. Bilinear characteristic due to opening and closing in kissing bond region results in nonlinear dynamic behavior of the structure such as harmonic distortion in response to harmonic excitation. So, the higher-order harmonics can be considered as Nonlinear Damage Indicator Functions (NDIF) for the purpose of damage identification. A two-dimensional (2D) finite element model of a beam connected to a rigid support via a flexible adhesive layer is used to investigate the efficiency of the proposed NDIFs in kissing bond detection. Kissing bond is introduced to the model via contact elements. NDIFs are extracted for the finite element model using single tone stepped-sine test simulation. Parameters such as amplitude of excitation, size and location of kissing bond region as well as friction between kissing surfaces, are studied. The results proved that the NDIFs are sensitive to the size and location of kissing bond. Consequently, in an experimental damage identification procedure, NDIFs can be used as an indicator of kissing bond type damages in adhesive joints.     

The PAR(p) Interconfigurations model used by the Brazilian Electric Sector

This study discusses the characteristics of the Periodic Autoregressive model, PAR(p), which is used to generate synthetic series of inflow energies that serve as entries for computer platforms that implement the planning and expansion of the operations of the BES – the Brazilian Electric Sector (SEB – Sistema Elétrico Brasileiro). The methodology for the design of a generating plant is presented in addition to the fundamentals of the “PAR(p) Interconfigurations” Model, which is referred to as the Inflow Energy Generation Model (IEGM) in this study. The major contribution of this study is to provide the first scientific discussion of the representation of multiple configurations using the PAR(p) model. For this purpose, several topics related to the time series are discussed, such as the definition of the model order, the matter of stationarity and the need to address possible outliers. Finally, a case study is presented, wherein the results of the estimation and generation of the described model’s scenarios are demonstrated.     

基于Q-learning的不确定环境BDI Agent最优策略规划研究

BDI模型能够很好地解决在特定环境下的Agent的推理和决策问题,但在动态和不确定环境下缺少决策和学习的能力。强化学习解决了Agent在未知环境下的决策问题,却缺少BDI模型中的规则描述和逻辑推理。针对BDI在未知和动态环境下的策略规划问题,提出基于强化学习Q-learning算法来实现BDI Agent学习和规划的方法,并针对BDI的实现模型ASL的决策机制做出了改进,最后在ASL的仿真平台Jason上建立了迷宫的仿真,仿真实验表明,在加入Q-learning学习机制后的新的ASL系统中,Agent在不确定环境下依然可以完成任务。